KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 1 5/9/2014 KSZ8864 Evaluation Board User’s Guide KSZ8864 Integrated 4-port 10/100 Ethernet
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 10 5/9/2014 7. Open the Windows and navigate to the directory where the Window SPI file is s
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 11 5/9/2014 connects to the port 3 MAC3 in the KSZ8864, and we refer to this as the port 3 Sw
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 12 5/9/2014 4.6.2 Port 3 SW3-MII Jumper and Register Configuration Modes JP42 Reg 223 Bit
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 13 5/9/2014 4.6.4 Port 3 SW3-RMII Jumper Configuration for KSZ8864 Modes JP42 JP41 JP24 J
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 14 5/9/2014 folder of MDC_MDIO MIIM of the software directory. For the SMI software to be use
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 15 5/9/2014 5.0 Software Description 5.1 Introducing Application Software Tools The Design Ki
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 16 5/9/2014 Found New Hardware Wizard window will pop-up and then follow the instructions ste
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 17 5/9/2014 Choose the ‘Install from a list or specific location (Advanced)’ radio button and
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 18 5/9/2014 5.3 DOS SPI Tool This is a simple and powerful tool to access all register. Th
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 19 5/9/2014 For Read or Write registers, reg is the offset address of the register, value
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 2 5/9/2014 Table of contents 1.0 Introduction ...
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 20 5/9/2014 Select ‘KSZ8864 4 port switch’ and click Next button, Pop up a MDIO MIIM Config
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 21 5/9/2014 5.5 MDC/MDIO SMI Software Tool 5.5.1 MDC/MDIO SMI software The software tool can
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 22 5/9/2014 Read register 1, display value with 0x40 and write bit1=1 to start switch with 0x
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 23 5/9/2014 Select the radio of I2C interface to do EEPROM configuration and press Continue
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 24 5/9/2014 Note: Chip ID1 has to set to 0x00 or 0x01 for EEPROM contents to be downloaded to
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 25 5/9/2014 After change the bits of the registers, the change can be written to EEPROM and s
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 26 5/9/2014 The control Window includes all registers, static MAC table, LAN table, dynamic
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 27 5/9/2014 MICREL, INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408)
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 3 5/9/2014 List of Figures and Tables Figure 1 KSZ8864 Evaluation Board ...
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 4 5/9/2014 1.0 Introduction The KSZ8864 is Micrel Operations’ new generation integrated 4-po
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 5 5/9/2014 4.0 Hardware Description The KSZ8864 evaluation board is in a compact form factor
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 6 5/9/2014 FIFO, Flow Control, VLAN Tagging, PriorityUSBDeviceUSBPortEEPROMPort 1 Port 2Por
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 7 5/9/2014 read the external EEPROM, if EEPROM does not exist, the chip will use the default
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 8 5/9/2014 JP30 SM3RXD2 Disable Back Pressure Enable Back Pressure JP31 SM3RXD1 Dr
KSZ8864 Evaluation Board User’s Guide Micrel Inc. Page 9 5/9/2014 JP4 MDIO Open JP8 Serial Bus Config. (PS0) Open JP9 Serial Bus Config. (PS
Commentaires sur ces manuels